3/4 hp, 115 VAC
1 phase, 60 Hz,
40 cu in
or glycerin filled
1 hp, 230/460 VAC
3 phase, 60 HZ,
See Pump Model Matrix for Specific Pump Number.
WARNING! The use of spool valves invalidates the warranty on VektorFlo® pumps.
Two stage pump, designed for power clamping, is medium weight (a fully equipped 2-Port pump weighs approximately 130 lbs) and energy efficient. Includes over pressure relief, full time pressure monitoring, in-tank fluid level sensor and full flow filtration.
First stage pump flow is 350 cu. in. per minute up to 650 psi to move clamps into position quickly. The second stage generates pressure with a flow rate between 40 and 50 cu. in/ min at 5,000 psi.
Exclusive stacking manifold feature accommodates all VektorFlo® D03 valves. Stacking of multiple manifolds allows you to select a pump to meet your circuit needs using inexpensive standard components
Protect your pump with our
new Return Line Filter
In operation, the pump turns on, builds to the preset pressure, then turns off. In the event of pressure decay, a pressure switch automatically restarts the pump to replenish system clamping pressure. The on-demand operation of the pump reduces electrical consumption and prevents overheating of oil which can occur in continuously running pumps.
The fluid level sensor prevents the pump from running without fluid. Should oil levels run low, the pump shuts down preventing potential damage.
Small size and high performance allow this pump to compete favorably with many single stage pumps requiring up to 2 hp motors.
Directional Control Valve Information..
Note: Maximum system flow rate is 1.5 gpm(346.5 cu. in./minute)for all VektorFlo® special function valves.
Excess flow voids warranty.
All dimensions are in inches.
Note: Cables omitted for clarity
Note: Pressure and return SAE 6 ports will not be used if pump is equipped with stacking blocks
Pump Systems Fully Configured Specifications
Number of Valves
Used as a central or remote power supply with remote
controlvalves configured with a "P" (pressure out) and
"T" (tank return flow)port only. Typically mounted behind
a machine or between twomachines with valvesmounted
on the machine closer to the application and often
machinecontrolled. A shear seal orpoppet stylezero
leak valve must be used.
Used to direct mount a valve to the pump, controlling
the direction of 2outlet ports. A shear seal or poppet style
zero leak valve must be used.
Valve installed with a control pendant to power systems
using the Self-closing Decoupler and TombstoneTop
Plates. Commonly referred as a dump pump and uses
a momentary contact pendant switch. When preset pressure
is reached the control valve automatically shifts and
dumps pressure back to tank. Operator interface is by
remote pendant or can be wired into a machine controller.
Engineered to reduce pressure to either the clamp or
unclamp side of a circuit. This model is ideal for use with
either 1 or 2 handed Auto-Shutoff Pallet Decouplers.
Uses a P-Blocked center valve to drop pressure in both
lines to decouple and re-couple the hydraulic hoses.
Operator interface is by remote pendant or can be wired
into a machine controller. This configuration can also
be used to operate two individual single acting systems
at different pressures
Engineered to be used with either 1 or 2 handed
Auto-Shutoff Pallet Decouplers. Uses a P-Blocked
center valve to drop pressure in both lines to decouple
and re-couple the hydraulic hoses. Operator interface
is by remote pendant or can be wired into a
Live or Decoupled Systems
Manual Pallet Decouplers, Tombstone Top
Plates and the Self-Closing (single hose) Decoupler.
Operator interface is by remote pendant or can be
wired into machine controller.
NOTE: All valves used in the decoupled
condition are de-energized when not in
use to avoid heat build-up between cycles.
To control a Single Acting system either coupled or
decoupled. (May not be used with 2 hose Auto-Shutoff
Decouplers.) Operator interface is by shifting a manual
valve handle, requiring pump to be located with in
Controls double acting systems, either coupled or
decoupled, when the fluid flow from the clamp and
unclamp hoses needs to return to tank the valve is
actuated to the "center" position. Recommended for
control of Auto-Shutoff Pallet Decoupler (2 hose)
systems. Operator interface is by shifting a manual
valve handle, requiring pump to be located with
in operators reach. This is an ideal configuration
for running double acting coupled or decoupled
systems. Best selection for fixture testing of all
We recommend use in a continuously connected system.
Not well suited for use with most decoupled
systems. Operator interface is by shifting a manual valve handle.
Recommended to run a single acting coupled system.
(May not be used with Auto-Shutoff Decouplers.)
wired into a machine controller. If this valve were
used to power a decoupled system, valves would
run hot while decoupled.
This valve is difficult to use with most decoupled
systems, generally we recommend use in a
continuously connected system. Operator interface
is by remote pendant or can be wired into a machine
controller. Center position allows no movement
of clamps when the valve is de-energized.
* Model numbers 55-9242-35, 55-9272-35, and 55-9292-35. are supplied with a 35-1446-10 (3/8" Dia. x 10') hose and 30-7827-60 (SAE 6 flat face female) quick connect.
Warning: The use of spool valves invalidates the warranty on VektorFlo® pumps.
NOTE: Contact factory for custom pump configurations.
NOTE: Voltages listed are input to control box for pump motor. All solenoid valves use24 VDC control voltage supplied by the transformer internal to the pump control box. Wiring of control valves supplied with pump is not required.
Solenoid valves configurations are supplied with one valve control pendant with a 6 ft. cable. For additional pendants order from the chart at the right.
NOTE: See pump manual to calculate the required
electrical service for your specific application.
* Use Vektek replacement filter only.
** DO3 manifold only pump has one valve manifold but no valve included. Order Model No. 62-5592-01 for pump
Model No. 62-5592-05
Mesh Size 24
Wire Diameter 0.014